We are having a group buy of 1000 gr soft jacketed
bullets for 12ga from Hawk. $2.10 each.Contact
me for details.Need order of 1000 total for them to
make dies and start.Got commitment for 400
already.Let me know if interested.Ed.

We got recoil now-Got a 1050 gr
Bridger over 2200 fps in the Savage.
I took the hollow base 750 gr Bridgers
made for me, and wedged in .500 caliber
slugs(I took out of 12ga sabot)in the base.
Added 300 gr. I was going to melt lead and put in,
but this was easier about 5 seconds,
after 15 seconds shortening nose on grinder
of .500 slug.Ed

WE are getting a replica of big 1887 12ga levergun to
test cases in. Should be interesting fun.Gun is here and
here is picture.Ed

http://www.gunownerstv.com/1887.jpg

Shot 12 double ought buckshot in 1887.
That's 624 grains worth. Used short
2.45 inch case that feeds from magazine.
Used fast ball powder, getting about
1500 fps. Further testing on 600 gr
hardened slug got 1700.That is in short
20 in barrel. Comparing this short case
with the 3.07 inch case I use in NEF there
is an inch difference in length of powder
column so it takes faster powder with
10k more pressure in 87 to get same velocities as in NEF. But the 1887 handles it fine.
It takes as much pressure as my Savage
in its present form.Ed

I got Rocky Mtn turned 12ga cases, and am
developing loads. They are 2 7/8 inches
long are for use in NEF and shortened
in 1887. These cases have shotgun
primers. Now these cases with shotgun primers and the two cases of ours we put small primers in don't fire the slow rifle powder loads
reliably,like cases with bmg primers.
Our testing is with 600 hardened Dixie slugs.
So I have and am testing slow shotgun powder and fast rifle.I tested 5 shotgun powders and
the primers fires then ok but the quick peak pressure when loads increased to get velocity
wanted in NEF caused too much case expansion just ahead of the base.Cases ejected ok but
that expansion and resizing will ruin cases
in a couple shots.These cases have a real thick base, and are machined to glass smooth finish.Nice cases.
I now testing AA1680 Ball and RE-7, they look good.
Have got loadswith 2 wads and slug in
the Rocky Mtn case, and only .002 expansion
of case ahead of base. Will chrono next and
expect it to get velocity we want in NEF.
Nice thing about this testing is that same loads will work in shortened 87 case by just
using less wad column.Ed

Got the NEF chambered for long case. And remember it
has beefed up hammer for bmg primers used in our case.
Got 2500 fps with 600 gr slug, cases eject out real easy,
8300 ft lbs from an NEF with 24 inch barrel.If you set up
NEF to use regular primers adapted to our case or
have Rocky Mtn make a long case you can do it without
a lot of work on the hammer and springs. Just use a
flake shotgun powder as a starter powder above the
primer, which how 700 NE and others are loaded.
Use 10 gr of flake and cut regular load 40 gr and
work up if pressures allow.Ed.

pretty cool...

don't bring it to california, though...i'm sure our paranoid "legislators" would want to outlaw it...

Been testing IMR-4759. No ignition problems.
Ignition is instant with regular primers.
Don't need Blue Dot starter powder,
like we had to do with RE-7 and RE-15
for good reliable ignition.We did 4759 in
plastic cases first.600 gr slug. I got a
nice working roll crimper attachment
for drill press for crimping slugs.
That sure makes it easy, and perfect crimp.
In 2 & 3/4 plastic cases with loaded
length of about 2.35 inches got to 80gr.
That's max as you must leave room for
about 3/8 wads or cushion wad. Some cases
may only hold 75 grains max due to
the case construction.Powder is less dense
than RE-15. 1650 plus fps in 24 inch barrel.
In 3 inch cases, loaded length about 2.6
inches, got to 95 grs max, 1800 plus fps.
Some cases may only hold 90 gr due to
case construction. Cushion is
a half inch felt wad or equivalent.
Both lengths start down and go up
if pressures allow. 60 gr short case,70 long.
This powder being faster than RE-15 you must
have a little cushion in the way of felt wads
or plastic cushion wads.With slower RE-15
a card wad works ok as powder started slower.
The powder burning must build pressure
to open crimp without a to high pressure spike.
This bulky powder with reliable ignition
is a winner.Then we tested 3" Rocky Mtn brass
cases, Got max load of 105 gr, and 1900 plus
fps. In few weeks will get the 4759 and RE-15
loads pressure tested.Ed

Now these loads are for only heavy barreled
steel action guns like the NEF Ultra 12,
or like my Savage with heavy barrel added.
I am getting heavy barrel on the 87 and
it will be long.There are some turn bolt
locking lug pumpguns that would work
with heavy barrels.There is a large
12ga Tula bolt action, but it's not imported.
This week if weather allows(no rain)
I will be firing first test loads of my
700HE long belted case.Ed.

Found an O/U that would handle the 4759 3"
loads. It is the Zoli Z-Sport. Expensive,
all alloy steel construction, tested to
about 100k. That's not a missprint.Their
site shows testing at the Italian proof house
of 8000 bar.That's 7-8 times regular shotgun
working loads.Pic of action below. It handling that extreme pressure, means that other quality
O/U like Ruger may handle 4759 loads.Ed

http://www.zoli.it/america/images_z/z_espedition2.jpg

Hot damnn- Test Results of 4 plastic cases.
Rem high base 3" case, with 600 gr
Dixie hardened slug. Roll crimped with
crimper in drill press. All 4 loaded with
90 gr of 4759. We have a winner.
Average velocity of 4 -- 1938 fps
Average pressure of 4 -- 14, 575 psi.
tested with transducer test ing setup,
in 30 inch barrel,In my 24" NEF I got 1800+.
Cases fell out of his test chamber like they did out of
my NEF.And with some cases I can get in 95gr,
that I figured with my math would
have 15k psi.So my math and developement is
OK.And 4800 ft lbs, thats neat with plastic.
Tom says this load will do in any gun that handles
the 2 oz factory magnum goose loads
that test about 13,600 to 14,000.And 4759
will give slower time to peak pressure, thus
will be easier on cases than magnum goose loads
or the hot factory Buckhamer slug loads
I fired, that expanded cases as much or more
than our 4759 loads.Ed

i may have missed the post but what exactly would these be used for?

Big game hunting in modern shotguns, with
regular chambers, like the NEF Ultra 12ga
slug gun or a Savage 210 12ga slug gun.Ed.

Buckhammer 3 "factory loads are 15k psi.
A 2.75 inch case with 80 gr of 4759, a thin card wad,
a 3/8 cushion lubed felt wad, when crimped is about
2.4 inches long, with 600gr Dixie slug. Based on
pressures recorded in previous post for 3 inch case
and 90gr of 4759, they will run about 13,400 psi,
and work through modern guns.Another load tested with
same bullet, 65gr of 4759, tested at same place
was 11,800 psi and 1640 fps. So you don't have
to put in my max loads, but go down a
little and use in modern guns that
are lighter than NEF so they don't kick so bad.But yet
you can get fairly good energy levels for big game, 3300
to 4000 ft lbs of energy.Ed

WE planning on a big action for 12GA FH.
Here is picture of top part of the
first scale-up model, next to smaller
Wickliffe. It has 12GA FH round in feed
trough. It is aluminum just for a model.
It will handle 12GA FH, 700HE, 700NE, 600NE,
etc. Bottom of block is flat to set on
mill table to do the machining.Next machining
will be the hole and slot down through the
action for breech block and hammer to
slide up and down in.Its taken awhile to
get some tooling.I had none when we set up
vertical mill, and have to get more.The
action model also will be narrowed up when
finished, and contoured to look as good
as the Wickcliffe.Ed.

http://www.gunownerstv.com/su.jpg